• SET-50 SET-50 SET-50 SET-50

    詳細信息

     品牌:TES華盛儀器  型號:SET-50  加工定制:是  
     測量范圍:0.68KG  測量精度:0.01 ° 外形尺寸:20*25*80 mm 
     用途:五金  長度:80 mm 工作溫度:25 ℃ 
     重量:1 ㎏ 裝箱數:1   

     


     

     


     

     

    利邊測試器

    利邊測試器是產品安全設備測試的領導者,當前在全世界製造業中廣泛使用,包括玩具、企業設備、汽車製造商及家電等。因為越來越多人關注家居產品的安全使用,所以 Underwriter’s Laboratory (UL)製訂出標準的測試儀器,去測試各種不同消費產品。

    美國TES華盛儀器公司是唯一利邊測試器SET-50的原生產商。

    如您關注您的產品利邊安全,並使之符合(UL公司及消費品安全委員會製訂的)國際標準,您必需購買利邊測試器SET-50及膠帽TC-3。

    利邊測試器是非常容易使用及耐用。貝殼形設計,特別適合放於手中,輕巧測試臂及完全密封式的軸承,可減少磨擦,加入新彈弓來符合*新的UL公司力度要求,所有可移動的部份均有保護來防止污垢及損壞。

    利邊測試器需配合膠帽一起使用,而膠帽是模彷人類手指厚度而設計。

     

    規格

    專為UL標準而設計的測試器。

    UL公司制定標準來決定電氣產品的鋒利邊程度(UL1439),這標準名為利邊測試器。提供一個客觀的標準,來決定符合現有的安全要求。
    大部份UL標準包括在消費產品上的主要要求例如邊緣、突出部份、角位、包圍物品、開口、圍邊、手把等等,這些部份都需要圓滑以不導致傷害。

     

    · 

    設計

    方便易用和長壽

    鋒利的邊緣測試器型號SET-50 由適合手型設計的貝殼狀機殼組成 (用Cycoloy 塑料製做, IBM 電腦機殼也選用同樣材料製造)。特點包括一條細小的手臂、被密封的滾珠軸承減少摩擦,並且加入新彈弓來符合*新的UL公司力度要求,所有可移動的部份均有保護來防止污垢及損壞。

    利邊測試器型號SET-50 配合膠帽TC-3使用。這成套工具包括42個膠帽,膠帽上附有三捲備用裝配的磁帶,方便在測試的工具上滑行。

    這個磁帶蓋帽符合U.L.三捲磁帶的要求:
    一層3M 泡沬材料為1/16”厚
    一層3M 泡沬材料為1/32”厚
    表面一層為聚四氟乙烯磁帶

    磁帶膠帽*有效率的用途是容易和迅速地對多個製造業進行測試,並且不用在測試前在工具上安裝三層不同的磁帶。每次測試須用磁帶膠帽,在幾秒鐘內它即可被除去、被辨認和被替換,因而可在很短時間內進行更多的測試。
    磁帶膠帽附的中心有1/16”的顯示,幫助審查員確認測試中心點。

     

    操作

    產品安全測試從未是這容易

    1. 磁帶蓋帽一直在利邊測試器的壓力頭以黑色為中心線和紅色塑料蓋帽面的部份滑行。

    2. 測試時,磁帶擺放在被檢查物件的邊緣上。用手拿著機殼,按下磁帶頭蓋, 直到測試臂及機殼形成直線。

    3. 沿邊緣2英寸移動壓力頭再返回起點。然後由邊緣撤出工具。邊緣與帽蓋頭之間的距離為4英寸。

    4. 檢查磁帶蓋帽確定是否穿透兩層感應器。如果穿透,黑色的磁帶將會被削減。利邊測試器可接受的鋒利程度是不可穿透感應器的外面兩層。

     

    關於TES公司

     

    成立於1990年,是利邊測試器及膠帽套的原生產商

    一部份著名生產商已經使用華盛公司的利邊測試器

    Amana Appliances
    Canon Corporation
    Coleman Products
    Eaton Corporation
    Electrolux
    Fujitsu
    General Electric
    Hamilton Beach/Procter Silex
    Hewlett-Packard
    Hot Point
    IBM
    La-Z-Boy
    Litton Corporation
    Mattel Maytag
    NEC America
    Nikon
    RCA
    Rheem
    Seksun Corporation
    Siemens Corporation
    Snapper
    Sunbeam
    Underwriters Laboratories
    Westbend Corporation
    Westinghouse
    Whirlpool
    Xerox

     

     

    English Version

     

     

    The Sharp Edge Tester is the leader in product safety equipment, currently in use worldwide by manufacturers of toys, home appliances, business equipment, automobile manufacturers, home appliances, every item used in the kitchen, and much more.

    With so much concern over the safety of products to be used in the home, Underwriter’s Laboratories has issued standards to test edge sharpness on a variety of consumer products.

    Technical Engineering Service (TES) is the original and only manufacturer of the Sharp Edge Tester Model SET-50.

    If you are concerned about the safety and sharpness of your product and want to meet international standards as set by UL and the Consumer Product Safety Commission, then you need to order the Sharp Edge Tester and Tape Cap Kit for use on your production line.

    The Sharp Edge Tester Model SET-50 is extremely easy to use and durable. It consists of a clam-shell type housing which fits into the palm of a hand. Features include a compact arm, sealed ball bearings to reduce friction, and a new spring to meet the latest Underwriter’s Laboratories force requirements. All moving mechanisms are protected against dirt and breakage. The Sharp Edge Tester is used with the available Tape Cap Kit which simulates the thickness of skin on the human finger.


    Specifications:

    This product was designed specifically for Underwiter’s Laboratories

    Underwriters Laboratories has released a “Standard for Determination of Sharpness of Edges of Electrical Equipment,” U.L. 1439. This standard calls for the use of the Sharp Edge Tester in order to provide an objective and uniform test method for determining compliance with an existing safety requirement.

    Most U.L. standards covering consumer products contain a subjective requirement such as “an edge, projection, or corner of an enclosure, opening, frame, guard, knob, handle, or the like, shall be smooth, well rounded, and not sufficiently sharp to constitute a hazard.”
    Based on recent publications, it is evident that the sharpness of edges on consumer products is important to many government agencies like the Consumer Product Safety Commission and the National Bureau of Standards. Comment from the industry — where thousands of Sharp Edge Testers are in use — favor the general design concepts of this U.L. chosen Sharp Edge Tester over all others.

    This model appeared in Production Magazine and in a technical paper of the “UL Sharp Edge Tester” #MR-77-469, published by the Society of Manufacturing Engineers.

    Note: If you have a new product to submit to ‘UL’ for approval. You must use this tool to test it’s EDGES. They will not approve your product without doing so.


    Design:

    Designed for Ease of Use and Longevity

    The Sharp Edge Tester Model SET-50 consists of a clam-shell type housing (made of Cycoloy plastic, the same material used to manufacture the housing of IBM computers) which fits into the palm of the hand. Features include a compact arm, sealed ball bearings to reduce friction, and a new spring to meet the latest Underwriter’s Laboratories force requirements. All moving mechanisms are protected against dirt and breakage.

    The Sharp Edge Tester Model SET-50 is used with the Tape Kit Model TC-3. This kit consists of 42 pieces each with three pre-assembled tapes on a plastic cap, which slips on to the tool for testing.
    This Tape Cap meets the U.L. requirements of three tapes:
    1 layer of 3M Scotch Foam, 1/16” thick,

    1 layer of 3M Scotch Foam, 1/32” thick,

    1 laver of skived Teflon Tape

    Use of the Tape Cap is the most efficient way for the inspector to easily and rapidly conduct multiple tests on the manufacturing line without having to install three different layers of tape on the tool prior to testing. Each time a test is performed with the Tape Cap, it can be removed, identified, and replaced within seconds; thus providing more tests in less time to facilitate inspection reports.

    The Tape Cap also features a 1/16” wide guide line which is on the center of the cap and helps the inspector performing the test to “center” the tape and the tool on the edge being tested.


    How to use:

    Product Safety Testing Has Never Been This Easy

    1. Slide the Tape Cap all the way on to the pressure head of the Sharp Edge Tester with the black center guide line and the uncovered portion of the red plastic cap facing up.

    2. Position the tape covered pressure head on the edge of the item to be checked for sharpness. Holding the clam shell base in your hand, press down on the tape covered head until the arm and the tool form a straight line.

    3. Move the pressure head two inches along the edge and then back again to the starting point. Then withdraw the tool from the edge. The total distance of engagement between the edge and the tape-covered head is therefore 4 inches.

    4. Examine the tape cap to determine whether or not penetration has occurred through the two-sensing layers. If penetration has occurred, the black indicating tape will be visible through the resulting cut. The application of the Sharp Edge Tester to an edge with acceptable sharpness will not result in the cutting through the two outer layers of the sensing tape.


    About TES:

    Technical Engineering Service is the original manufacturer of the Sharp Edge Tester and Tape Cap Kit. We have been manufacturing this product since 1973.

    Some of Companies which have used the Sharp Edge Tester:

    Amana Appliances
    Canon Corporation
    Coleman Products
    Eaton Corporation
    Electrolux
    Fujitsu
    General Electric
    Hamilton Beach/Procter Silex
    Hewlett-Packard
    Hot Point
    IBM
    La-Z-Boy
    Litton Corporation
    Mattel Maytag
    NEC America
    Nikon
    RCA
    Rheem
    Seksun Corporation
    Siemens Corporation
    Snapper
    Sunbeam
    Underwriters Laboratories
    Westbend Corporation
    Westinghouse
    Whirlpool
    Xerox


    Ordering Information


     

    SET-50 sharp edge tester plus TC-3 Tap Cap (includes 44 piece)

    HK$4,650 per set

    Buy It Now


    TC-3 Tape Cap (includes 44 piece)

    HK$1,800 per box

    Buy It Now

    Made in the USA

     

     

     

       買家在收到貨時,請與貨運公司人員當面驗貨再簽收!請仔細檢查配件是否齊全,外觀有無損壞,特別是外觀有無破損,如有損壞或是配件丟失,請您拒收,并立即聯系東莞華盛公司協商處理!若您不驗貨檢查就簽收(例如簽收后才發現外觀損壞或配件丟失.恕本公司概不負責)造成的損失由買家自行承擔(買家簽收后本公司將視為產品完好到貨)因本公司一直堅持薄利多銷原則.還請大家多多配合.謝謝大家的理解和支持!

     

      

       華盛儀器有限公司是集研發、生產銷售于一體的實驗儀器專業制造商。我公司專業致力于研發、生產高品質的現代化實驗設備,已通過了ISO9001/2000國際質量體系認證,公司擁有先進的生產及檢測設備,并具有完善的計量及質量保證體系。
        公司主要產品有:玩具檢測儀器類系列、環境試驗箱類系列、電子測量儀器類系列、空氣壓縮機類系列、冷凍式干燥機類系列等基礎實驗室設備,并廣泛應用于生物制藥、衛生防疫、環境保護、農業科研等領域。我們本著以客戶服務為導向,為客戶提供實驗室儀器及電子行業生產設備的整體解決方案和專業化服務。我們的經營理念是“客戶,以質量為本”,為目標市場提供一流的服務,使客戶得到*大的增值,與客戶建立長久、互贏、雙贏的合作伙伴關系。
        華盛將一如既往,以實事求是、踏實苦干為根本;以國際先進水平為目標,不斷攀登技術高峰;以市場為導向,不斷把高質量的產品奉獻給廣大客戶。

     

     

    聯 系 人:游國林 先生

    電    話:

    移動

    地    址:中國 東莞市黃江鎮西路三街18號

    郵    編:523750

    我公司已在全國各省市有自己的辦事處及售后服務點!您購買我公司產品,我公司給您品質保障!
  • 留言

    詢價產品:
    *(必填)
    聯系人: *(必填)
    手    機: *(必填)
    電    話:
    E-mail:
    公    司: *(必填)
    地    址:
東莞市黃江華盛儀器經營部 地址: 中國廣東省東莞市黃江鎮西進路三巷18號 技術支持:谷瀑環保 免責申明 管理員入口
內容聲明:谷瀑環保為第三方平臺及互聯網信息服務提供者,谷瀑環保(含網站、客戶端等)所展示的商品/服務的標題、價格、詳情等信息內容系由店鋪經營者發布,其真實性、準確性和合法性均由店鋪經營者負責。谷瀑環保提醒您購買商品/服務前注意謹慎核實,如您對商品/服務的標題、價格、詳情等任何信息有任何疑問的,請在購買前通過谷瀑環保與店鋪經營者溝通確認;谷瀑環保設備網上存在海量店鋪,如您發現店鋪內有任何違法/侵權信息,請在谷瀑環保首頁底欄投訴通道進行投訴。
河北快3开奖结果图号